(The replacement model number HDG2000B Series )
Model | HDG1022A | HDG1012A |
Frequency range(sine) | 40uHz~20MHz | 40mHz~10MHz |
Output Characteristics of Channel A | ||
Waveform Characteristics | ||
Waveform type | sine, square, pulse, DC | Sine, Square, Triangle, Ramp, Pulse etc. |
Waveform length | 4 ~ 16000 points | 1024 points |
Sample rate | 180MSa/s | 100MSa/s |
Waveform amplitude resolution | 10bits | 8bits |
Sinusoidal harmonic rejection | ≥50dBc (≤1MHz), ≥ 40dBc (1MHz ~ 20MHz), ≥30dBc (20MHz ~ 40MHz) | ≥40dBc (<1MHz), ≥35dBc (1MHz~20MHz) |
Sine wave total distortion | ≤0.5 % (20Hz ~ 200kHz) | ≤1% (20Hz~200kHz) |
Pulse and square rise/fall time | ≤20ns | ≤35ns |
Pulse and square overshoot | ≤5% | ≤10% |
Square wave duty cycle | 50% | 1%~99% |
Pulse wave duty cycle | 0.1%~ 99.9% | -- |
Frequency Characteristics | ||
Frequency range | sine:40μHz ~ 2kHz, resolution: 40μHz; 2kHz ~ the Max.frequency, resolution: 40 mHz; square: 40μHz~20mHz; pluse:40μHz~10mHz | sine: 40mHz~Max.frequency (MHz); |
square: 40mHz~5MHz; | ||
other waveforms: 40mHz~1MHz; | ||
Frequency resolution | -- | 40mHz |
Frequency accuracy | ±(5×10-5+40mHz) | ±(5×10-5+40mHz) |
Frequency stability | ±5×10-6/3 hours | ±5×10-6/3 hours |
Amplitude Characteristics | ||
Amplitude range | 2mVpp ~ 20Vpp (high impedance) |
2mVpp~20Vpp 40mHz~10MHz (high impedance); 2mVpp~15Vpp 10MHz~15MHz (high impedance); 2mVpp~8Vpp 15MHz~20MHz (high impedance) |
Amplitude resolution | 20mVpp (amplitude>2Vpp), 2mVpp (amplitude<2Vpp) | |
Amplitude accuracy | ±(1%+2mVrms) (high impedance, RMS, 1kHz) | ±(1%+2mVrms) (high impedance, RMS, 1kHz) |
Amplitude stability | ±0.5%/3 hours | ±0.5%/3 hours |
Amplitude flatness | ±5% (frequency<1MHz), ±10% (1MHz ~ 10MHz), | ±5% (frequency<10MHz), |
±20% (frequency between 10MHz ~ 60MHz) | ±10% (frequency >10MHz) | |
Output impedance | 50Ω | 50Ω |
Sine wave amplitude setting range (50Ω) | 1mVpp ~ 10Vpp, when output frequency ≤10MHz; | -- |
1mVpp ~ 5Vpp, when output frequency ≤40MHz; | ||
1mVpp ~ 2Vpp, when output frequency ≥ 40MHz; | ||
Amplitude setting range (high impedance) | 2mVpp ~ 20Vpp, when output frequency ≤10MHz; | -- |
2mVpp ~ 10Vpp, when output frequency ≤40MHz; | ||
2mVpp ~ 4Vpp, when output frequency ≥40MHz ; | ||
Offset Characteristics | ||
Offset range | ±10V (high impedance) | |
Resolution | 20mVdc | |
Offset accuracy | ±(1%+20mVdc) | |
Sweep Characteristics(linear sweep on frequency or amplitude) | ||
Sweep range | free to set start point and stop point | |
Sweep step | any value more than resolution | |
Sweep rate | 10ms~60s/step | |
Sweep mode | Up, Down, Up-Down | |
Manual sweep | step/time | |
Frequency Modulation Characteristics | ||
Modulation signal | internal or external waveforms | internal signal, channel B or external waveforms |
FM deviation | 0%~20% | 0%~20% |
Carrier signal | -- | channel A signal |
Amplitude Modulation Characteristics | ||
internal or external waveforms | internal or external waveforms |
|
0%~120% | 0%~120% |
|
Shift Keying Characteristics | ||
FSK | free to set carrier frequency and hop frequency | |
ASK | free to set carrier amplitude and hop amplitude | |
PSK | hop phase 0~360°, resolution 11.25° | hop phase 0~360°, resolution 1° |
Alternative rate | 10ms~60s | 10ms~60s |
Output Characteristics of Channel B | ||
Waveform Characteristics | ||
Waveform type | 32 kinds of waveforms, like sine, square, triangle, sawtooth, ladder etc. | |
Waveform length | 1024 points | |
Sample rate | 12.5MSa/s | |
Waveform amplitude resolution | 8bits | |
Frequency Characteristics | ||
Frequency range | Sine: 10mHz~1MHz; Other waveforms: 10mHz~100kHz | |
Frequency resolution | 10mHz | |
Frequency accuracy | ±(1×10-5+10mHz) | |
Amplitude Characteristics | ||
Amplitude range | 50mVpp~20Vpp (high impedance) | |
Amplitude resolution | 20mVpp | |
Output impedance | 50Ω | |
Harmonic Characteristics (channel B frequency is the harmonic wave of channel A) | ||
Harmonic time | 0.1 ~ 250.0 times | -- |
Harmonic frequency | <1MHz | -- |
Phase adjustment | coarse adjustment: 11.25 degree/step, fine adjustment: 2 degree/step | -- |
Burst Characteristics(channel B signal is used as burst signal) | ||
Frequency of Channel B | 40mHz ~ 1MHz | |
Burst Frequency | 10mHz ~ 50kHz | |
Burst count | 1~65000 cycles | |
Burst mode | continuous burst and single burst | |
TTL Output Characteristics | ||
Waveform characteristics | Square, rise/fall time≤20ns | |
Frequency characteristics | same as sine wave of channel A | 10mHz~1MHz |
Amplitude characteristics | TTL, CMOS compatible, low level<0.3V, high level>4V | |
Common Characteristics | ||
Power source | Voltage: AC220V (1±10%), AC110V (1±10%) (Pay attention to the position of voltage selection switch); Frequency: 50Hz (1±5%) Power: <45VA | |
Environment | Temperature: 0~40℃ Humidity: <80% | |
Operation characteristics | Key operation for all functions, menu display, rotary dial adjustment | |
Display | TFT display, 320*240, English, Chinese (simplified), Chinese (traditional) | |
Mechanical | 415mm×295mm×195mm; 3.5kg | |
Manufacturing technology | Surface Mount Technology, Integrated Circuit. High reliability and stability. | |
Optional Parts Characteristics | ||
Frequency counter | Testing frequency range: 1Hz~200MHz;Input signal amplitude: 100mVpp~20Vpp | |
Max. output power: 7W (8Ω), 1W (50Ω) Max. output voltage: 22Vpp | ||
Power amplifier | Frequency bandwidth: 1Hz-200kHz |
|
|
|
|
|
|